1. Identificação | |
Tipo de Referência | Artigo em Revista Científica (Journal Article) |
Site | mtc-m16c.sid.inpe.br |
Código do Detentor | isadg {BR SPINPE} ibi 8JMKD3MGPCW/3DT298S |
Identificador | 8JMKD3MGP8W/34DNGKP |
Repositório | sid.inpe.br/mtc-m18@80/2008/12.18.13.35 (acesso restrito) |
Última Atualização | 2009:12.14.18.20.44 (UTC) administrator |
Repositório de Metadados | sid.inpe.br/mtc-m18@80/2008/12.18.13.35.34 |
Última Atualização dos Metadados | 2018:06.04.03.56.02 (UTC) administrator |
Chave Secundária | INPE--PRE/ |
DOI | 10.1016/j.matdes.2008.09.041 |
ISSN | 0261-3069 |
Chave de Citação | SouzaNonRibMacSil:2009:CuFoTu |
Título | Cutting forces in turning of gray cast iron using silicon nitride based cutting tool |
Ano | 2009 |
Mês | Aug. |
Data de Acesso | 19 maio 2024 |
Tipo Secundário | PRE PI |
Número de Arquivos | 1 |
Tamanho | 375 KiB |
|
2. Contextualização | |
Autor | 1 Souza, J. Vitor C. 2 Nono, Maria do Carmo Andrade 3 Ribeiro, M. V. 4 Machado, João Paulo Barros 5 Silva, O. M. M. |
Grupo | 1 LAS-CTE-INPE-MCT-BR 2 LAS-CTE-INPE-MCT-BR 3 4 LAS-CTE-INPE-MCT-BR |
Afiliação | 1 Instituto Nacional de Pesquisas Espaciais (INPE) 2 Instituto Nacional de Pesquisas Espaciais (INPE) 3 FEG-UNESP 4 Instituto Nacional de Pesquisas Espaciais (INPE) 5 CTA-IAE/AMR |
Revista | Materials & Design |
Volume | 30 |
Número | 7 |
Páginas | 2715-2720 |
Histórico (UTC) | 2010-04-23 17:16:48 :: simone -> administrator :: 2018-06-04 03:56:02 :: administrator -> marciana :: 2009 |
|
3. Conteúdo e estrutura | |
É a matriz ou uma cópia? | é a matriz |
Estágio do Conteúdo | concluido |
Transferível | 1 |
Tipo do Conteúdo | External Contribution |
Resumo | This paper presents the results of an experimental investigation about the effect of cutting forces on gray cast iron turning using silicon nitride (Si3N4) based ceramic tool. Turning experiments were carried out at five different cutting speeds and feed rates while depth of cut was kept constant. Tool performance was evaluated with respect to tool wear, temperature, surface finish produced and cutting forces generated during turning. The Si3N4 based ceramic cutting tool showed high performance when increasing cutting speed. These results can be associated with good high-temperature strength of the cutting tool and the presence of graphite flakes in gray cast iron, that lower the friction coefficient between the cutting tool/workpiece. |
Área | FISMAT |
Arranjo | urlib.net > BDMCI > Fonds > Produção anterior à 2021 > LABAS > Cutting forces in... |
Conteúdo da Pasta doc | acessar |
Conteúdo da Pasta source | não têm arquivos |
Conteúdo da Pasta agreement | não têm arquivos |
|
4. Condições de acesso e uso | |
Idioma | en |
Arquivo Alvo | cutting forces.pdf |
Grupo de Usuários | administrator simone |
Visibilidade | shown |
Política de Arquivamento | denypublisher denyfinaldraft24 |
Permissão de Leitura | deny from all and allow from 150.163 |
|
5. Fontes relacionadas | |
Unidades Imediatamente Superiores | 8JMKD3MGPCW/3ESR3H2 |
Acervo Hospedeiro | sid.inpe.br/mtc-m18@80/2008/03.17.15.17 |
|
6. Notas | |
Campos Vazios | alternatejournal archivist callnumber copyholder copyright creatorhistory descriptionlevel dissemination documentstage e-mailaddress electronicmailaddress format isbn keywords label lineage mark mirrorrepository nextedition notes orcid parameterlist parentrepositories previousedition previouslowerunit progress project readergroup resumeid rightsholder schedulinginformation secondarydate secondarymark session shorttitle sponsor subject tertiarymark tertiarytype typeofwork url versiontype |
|
7. Controle da descrição | |
e-Mail (login) | marciana |
atualizar | |
|